*Titebond WeatherMaster - Translucent (#44011) is not paintable. Due to high heat, it is NOT recommended to store sealants above the second shelf (>20 feet high) in a warehouse. Contact with asphalt or butyl may cause discoloration, but will not affect product performance. For best results, store in a dry location at or below 75☏. Sealant releases methanol during cure, check with substrate manufacturer for compatibility. Check with polycarbonate supplier on compatibility. Application of sealant at high temperatures may cause the sealant to sag in some applications. It is highly recommended to use backing material. Once sealant is applied, do not wipe with solvents or tooling aids such as soaps or oils. Air, sealant and surface temperature should be above 0☏. Limitations: Not designed for continuous submersion or use below the waterline. Tremflex 834 is a pure acrylic latex sealant formulated to provide a fast-setting pliable seal with minimal shrinkage. Follow solvent vendor’s precautions when using solvents. After curing, excess sealant must be cut or scraped away. Cleanup: Clean uncured material with acetone or isopropyl alcohol. For other paint types, a compatibility test is recommended. It is recommended to paint over sealant with a shellac-based primer before painting. In most cases, painting may occur one hour after application with a high-quality acrylic, water-based (latex) paint that does not contain plasticizer. If used indoors, sealant may need to be painted. Painting: Sealant is intended for exterior use. For questions, please call our Help Line at 1-80. Do not apply WeatherMaster Translucent to polycarbonate due to solvent cracking. For use on polycarbonate, check with polycarbonate supplier on compatibility. Substrate Compatibility: If application is for Kynar™ coated materials, use WeatherMaster Metal Roof Sealant. It is the sole responsibility of the user to thoroughly test any proposed use with all substrates to determine project suitability. Once sealant is dry to the touch and does not transfer, remove masking tape. To ensure neat sealant lines, mask areas adjacent to joints. Screw nozzle onto cartridge and cut tip on slant for 1/4" to 3/8" bead and place in cartridge gun. Remove nozzle, cut tip of the nub and puncture inner foil seal. Surfaces must be clean and free of any material that may prevent adequate adhesion. to 212☏ (-59☌ to 100☌) white & colors, -75☏ to 250☏ (-59☌ to 121☌) crystal clear (may discolor at higher temperatures), -40☏ to 400☏ (-40☌ to 204☌) translucent Method of Application: Cartridge/caulking gun Tooling Time: For a 1/4" bead, approximately 10-15 minutes, depending on temperature and humidity. Application Temperature: Above 0☏ (-18☌) Service Temperature Range: -75☏. Tremco 834 latex sealant comes in 10.1 fluid ounce cartridges and 20 ounce sausages.Application Guidelines Complete Installation Instructions: For complete installation instructions, please visit our Sealant Installation Guide for more information. Tremco 834 latex sealant has also been tested for acoustical properties to reduce sound transmissions when constructing partition walls. This sealant can be used either indoors or outdoors, becomes tack-free in only 15 minutes and is ready to be painted, if desired, in 30 to 45 minutes using either latex or oil-based paint. Tremflex 834 is an easy gunning, non-staining, general purpose sealant that is formulated from the highest quality acrylic polymer to offer outstanding flexibility and workability for any commercial construction acrylic sealant application. It is suitable for use on vinyl, aluminum and wood siding as well as on bathroom and kitchen fixtures. The 834 series sealant by Tremco is also highly recommended as an acoustical seal when constructing interior walls, ceilings and floors. Tremflex 834 can be used for general purpose interior and exterior caulking and as a back-bedding glazing compound. Tremco Tremflex 834 is a pure acrylic, latex sealant that is formulated to provide a quick-setting, flexible seal with minimal shrinkage.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |